Skip to content

Command line tools

Docker proxy setup

Want to run Docker through a proxy? Docker can pass proxy settings to containers and to builds through its client configuration. Below is the exact setup, a working example, how countries and addresses work, and a short list of fixes for the errors people hit most often.

You need an active DataImpulse proxy first. Create an account, add funds from US$1, and order a proxy in one of the 62 countries we stock. The dashboard then shows the host, port, username and password. If you have not done that yet, start with the quick-start guides.

Tool
Docker
Category
Command line tools
Proxy protocol
HTTP with username and password
Example host
203.0.113.10
Countries in stock
62

What you need from your dashboard

Every DataImpulse proxy has the same four values, and each proxy has its own. The example values below are placeholders, so always copy the real ones from your dashboard. There is nothing to add to the username: the country was chosen when you ordered.

SettingExampleWhat it is
Host203.0.113.10The proxy's address, usually an IP, shown with the proxy in the dashboard
Port8080The proxy's port, which differs from proxy to proxy
UsernameusernameThe proxy username, used exactly as shown
PasswordpasswordThe proxy password. Treat it like any other secret
ProtocolHTTPUse an http:// proxy URL, even for HTTPS sites

Set up Docker with a DataImpulse proxy

Docker is a command line tool. The example below is complete and runs as it is once you replace the host, port, username and password with your own values.

  1. Make sure Docker is installed and up to date.
  2. Build the proxy URL from your dashboard values: http://USERNAME:PASSWORD@HOST:PORT.
  3. Pass the proxy to Docker as shown in the example.
  4. Request an IP echo page such as https://httpbin.org/ip and read the address it returns.
  5. Add a timeout and a retry limit before you run a larger job.
# ~/.docker/config.json
{
  "proxies": {
    "default": {
      "httpProxy": "http://username:[email protected]:8080",
      "httpsProxy": "http://username:[email protected]:8080",
      "noProxy": "localhost,127.0.0.1"
    }
  }
}

Countries and addresses

You choose the exit country when you order, and every proxy in the order is an IP registered in that country. There is nothing to add to the username in Docker: enter the credentials exactly as the dashboard shows them.

Each proxy keeps the same address for the whole rental period, so a session in Docker stays on one address by default. To work from another country, or to spread work across several addresses, order more proxies and give each one its own profile, connection or entry in Docker.

Check that Docker is really using the proxy

Do not assume. Verify the connection before your real job starts, and again after any change to the settings.

  1. Request https://httpbin.org/ip or any IP lookup page with Docker.
  2. Compare the address with your own. It must be different.
  3. Check the country in two lookup tools and compare it with the country you ordered.
  4. Repeat the request once. The address should stay the same, because each proxy keeps its address for the rental period.

Fixing common Docker proxy problems

These are the problems we see most often, with the fix that usually works.

  • 407 Proxy Authentication Required. The username or password is wrong, or the tool did not send them. Copy both from the dashboard again, from the same proxy as the host and port.
  • Connection timed out. The host or port is wrong, or a firewall blocks the port. Try curl first to separate a tool problem from a network problem.
  • The exit country is not the one you expected. Look the address up in two lookup tools, because databases do not always agree, and check that you used the proxy from the order for that country.
  • TLS or certificate errors on HTTPS pages. Use an HTTP proxy URL (http://...) for the proxy itself, even when the website is HTTPS. The proxy opens a tunnel and does not inspect the traffic.
  • Pages load slowly. Lower your concurrency, reuse connections and try a proxy in a country closer to the target.
  • The site blocks you. Slow down, send realistic headers, and consider an ISP proxy if the site is strict about datacenter ranges.
  • Your balance ran out. Check the dashboard. Orders are paid from your balance, and an expired rental stops working.

Good habits when you use Docker with a proxy

A proxy only changes the address your traffic comes from. These habits make the difference between a setup that lasts and one that does not.

  • Keep credentials out of your shell history. Read the password from an environment variable or a file only you can read.
  • Run a single test request before you start a batch, and look at the exit address it reports.
  • Remove proxy settings when you finish, so ordinary traffic does not run through a rented address.
  • Add a timeout or retry limit so one stalled request does not block a script.
  • Respect the terms of the site you are downloading from or checking.

This file configures containers you start with the Docker client. To proxy image pulls by the Docker daemon, set the proxy in the daemon's service configuration instead.

Using proxies responsibly in any country

A proxy is a networking tool and it is lawful in most places, but what you do with it still has to be lawful and fair. Follow the laws that apply to you and to the place you send traffic to, read the terms of the sites you visit, honour robots rules and rate limits, and never use an address to access accounts or data that are not yours. DataImpulse cannot give legal advice, and our acceptable use policy applies to every order.

In practice that means reading public pages, checking your own sites and ads, and testing your own products. If a task would be unwelcome to the site owner when done by hand, it is unwelcome when done through a proxy too.

Frequently asked questions

Does Docker work with DataImpulse proxies?

Yes. DataImpulse proxies are standard HTTP proxies with username and password authentication, and Docker supports that kind of proxy. Use the setup above and verify the address with an IP lookup.

What proxy settings do I enter in Docker?

Enter the host, the port, the username and the password of your proxy from the DataImpulse dashboard. Use HTTP as the proxy type.

Why does Docker show a 407 error?

A 407 means the proxy did not accept the credentials. Copy the username and password again, check for extra spaces, and make sure they belong to the same proxy as the host and port. Also check that the rental period has not ended.

Can I choose the country in Docker?

You choose it when you order. Every proxy in the order is registered in that country, so use the proxy for the country you need and check it with an IP lookup.

How do I keep the same IP in Docker?

Keep using the same proxy. Each proxy keeps its address for the whole rental period. For a different address, use another proxy from your order.

Is it safe to put my proxy password in Docker?

It is as safe as any other password in that tool. Do not share exported settings or projects that contain it, do not commit it to a repository and tell support right away if it leaks.

Ready to try it?

Create an account, add funds from US$1 and pick your country and proxy type.